2012年01月10日
SEALs upgrade to SIG Sauer P226 Mk25 Pistol
私たちのブログを訪問していただきありがとうございます。あなたがお持ちの場合DIYの要求は私達に電子メールを送信してください。
Back in the 80s the US Naval Surface Warfare Center (NSWC) procured SIG Sauer P226 pistols for the SEALs. The NSWC version of the P226 was later sold to the public as the SIG P226 Navy. The Navy has recently given the latest version of their P226 the designation Mk25 and SIG is now selling the Mk25 to public. It is the one with the anchor logo on the slide.
Photos from the firearmblog
A light hearted video of the P226
NEWS ARCHIVES
Back in the 80s the US Naval Surface Warfare Center (NSWC) procured SIG Sauer P226 pistols for the SEALs. The NSWC version of the P226 was later sold to the public as the SIG P226 Navy. The Navy has recently given the latest version of their P226 the designation Mk25 and SIG is now selling the Mk25 to public. It is the one with the anchor logo on the slide.
Photos from the firearmblog
A light hearted video of the P226
NEWS ARCHIVES
2012年01月10日
Magpul MOE Scout mount
私たちのブログを訪問していただきありがとうございます。あなたがお持ちの場合DIYの要求は私達に電子メールを送信してください。
Magpul just released their new MOE Scout Mount. The MOE Scout Mount is a cantilevered weapon light attachment point that connects directly to the Magpul MOE hand gaurd. The new Magpul MOE Scout Mount was designed for use with Surefire Scount Lights but should work with many other 1913 Picatinny mounted lights. Made in the USA, the MOE Scout Mount is available in both right and left hand configurations and positions your weapon light at 11 o’clock high with the left hand model and one o’clock with the right.
Also available in our stores
NEWS ARCHIVES
Magpul just released their new MOE Scout Mount. The MOE Scout Mount is a cantilevered weapon light attachment point that connects directly to the Magpul MOE hand gaurd. The new Magpul MOE Scout Mount was designed for use with Surefire Scount Lights but should work with many other 1913 Picatinny mounted lights. Made in the USA, the MOE Scout Mount is available in both right and left hand configurations and positions your weapon light at 11 o’clock high with the left hand model and one o’clock with the right.
Also available in our stores
NEWS ARCHIVES
2012年01月10日
VSR-10 Gspec Takedown and Upgrade
私たちのブログを訪問していただきありがとうございます。あなたがお持ちの場合DIYの要求は私達に電子メールを送信してください。
This my Tokyo Marui Gspec. This is full stock and shooting at 89m/s. I will show a step by step takedown and will also show you how to make it shoot at 96-98m/s just by changing the inner brass barrel with the PSS10 430 mm 6.03 barrel.
I will be installing the following:
PDI light bull barrel
PDI bull barrel cap
PDI barrel space
PSS10 6.03 tightbore barrel 430mm
First remove the dummy silencer (you dont have have to if you ample space). Then remove these two screws near the magazine well. after removing screws you can pull the upper assembly out in upward motion.
This is the mag catch assembly, be careful because they have a tendency to fly off and they are hard to find.
Showing the upper separated from the lower.
Now remove this screw.
And loosen these two screws, no need to remove. You just need to loosen them so you can unscrew the barrel from the barrel base.
After separating the barrel from the barrel base, you are now ready to remove the inner barrel assembly. First remove these two screws.
Also take out this screw to remove the hop-up lever.
Now we are ready to replace the TM brass barrel with the PSS10 barrel
First remove the 3 screws that holds the barrel (in green) and then the two screws (in red) to open the hop assembly
All disassembled as shown here. Just replace the barrel and reassemble it back.
Now to prepare the bull barrel, first we need to insert the barrel spacer inside the bull space. They are a little bit tight but I rubbed a few drops of silicon into the o-rings.
Then using the brass barrel I removed to push it into place
Now you are ready to insert the inner barrel assembly
Push it into place and make sure these two holes are aligned. It is where one of the screw goes. After aligning, you also need the put back the hopup lever.
As shown here you are ready to screw on the barrel into the barrel base
I suggest using a little bit of teflon tape
You can also remove the hop sticker into the new one
And install the bull barrel cap anywhere during the process
And from here it is just reverse reassembly and you have new look. In installing the 430mm PSS10 tightbore barrel you gain at least 7-9m/s. I already upgraded 3 gspec with just that barrel and it is always the case. I havent tried the pdi since I am already getting good results with the laylax PSS10.
Photos of the final look of my VSR will be posted after I out the finishing touches. I am planning to paint it and I will also post the process here so keep posted.
NEWS ARCHIVES
This my Tokyo Marui Gspec. This is full stock and shooting at 89m/s. I will show a step by step takedown and will also show you how to make it shoot at 96-98m/s just by changing the inner brass barrel with the PSS10 430 mm 6.03 barrel.
I will be installing the following:
PDI light bull barrel
PDI bull barrel cap
PDI barrel space
PSS10 6.03 tightbore barrel 430mm
First remove the dummy silencer (you dont have have to if you ample space). Then remove these two screws near the magazine well. after removing screws you can pull the upper assembly out in upward motion.
This is the mag catch assembly, be careful because they have a tendency to fly off and they are hard to find.
Showing the upper separated from the lower.
Now remove this screw.
And loosen these two screws, no need to remove. You just need to loosen them so you can unscrew the barrel from the barrel base.
After separating the barrel from the barrel base, you are now ready to remove the inner barrel assembly. First remove these two screws.
Also take out this screw to remove the hop-up lever.
Now we are ready to replace the TM brass barrel with the PSS10 barrel
First remove the 3 screws that holds the barrel (in green) and then the two screws (in red) to open the hop assembly
All disassembled as shown here. Just replace the barrel and reassemble it back.
Now to prepare the bull barrel, first we need to insert the barrel spacer inside the bull space. They are a little bit tight but I rubbed a few drops of silicon into the o-rings.
Then using the brass barrel I removed to push it into place
Now you are ready to insert the inner barrel assembly
Push it into place and make sure these two holes are aligned. It is where one of the screw goes. After aligning, you also need the put back the hopup lever.
As shown here you are ready to screw on the barrel into the barrel base
I suggest using a little bit of teflon tape
You can also remove the hop sticker into the new one
And install the bull barrel cap anywhere during the process
And from here it is just reverse reassembly and you have new look. In installing the 430mm PSS10 tightbore barrel you gain at least 7-9m/s. I already upgraded 3 gspec with just that barrel and it is always the case. I havent tried the pdi since I am already getting good results with the laylax PSS10.
Photos of the final look of my VSR will be posted after I out the finishing touches. I am planning to paint it and I will also post the process here so keep posted.
NEWS ARCHIVES
2012年01月10日
Umarex / IWI UZI .22 LR Rifle and Pistol
私たちのブログを訪問していただきありがとうございます。あなたがお持ちの場合DIYの要求は私達に電子メールを送信してください。
Umarex USA are importing .22 pistols and rifles patterned on the famous UZI machine gun. The guns are manufactured by Carl Walther in Germany but are branded IWI (the official UZI manufacturer). There are two models. The rifle model modeled after the UZI carbine and includes a folding stock and faux suppressor. The pistol model is modeled after the Micro UZI machine pistol.
Uzi rifle
Uzi pistol
Story and photos from firearmblog
NEWS ARCHIVES
